Water not filling the toilet? Here’s what to do.
A slow flowing toilet tank can be a sign of bigger issues. If you don’t deal with it quickly you could find yourself with a toilet tank that won’t fill with water at all. Here is how you fix a toilet tank that is not filling with water. Best of all you can do all of these without calling a plumber.
Why is My Toilet Tank Not Filling with Water?
The reason your tank isn’t filling with water will be one of several reasons. The first one is that the flapper isn’t properly closing. This will leave you with a running toilet because all the water is coming into the tank and draining right back down into the toilet bowl.
The next reason is that you have debris clogging the main water line coming into the tank. This can cause a slow filling tank or tank not having any water come through it all. This means that the line and/or the fill valve will need to be flushed. Don’t worry it’s easier than it sounds.
The third reason Is that the toilet float is stuck or broken and will need to be adjusted or replaced.
Finally the overflow tube may be cracked and water is going into the toilet bowl instead of filling up the tank.
Step 1: Take of the lid of the tank
The first thing you’ll do is remove the lid of the toilet tank. Place it on a flat surface out of hte way. Toilet tank lids can break if pressure is put on the wrong spot and they are expensive to replace.
Step 2: Inspect the tank
Check the tank to make sure that there is water flowing into the tank. Next, in the following order check these four items.
Toilet flapper is closing
The toilet flapper should be closing and making a tight seal. If your toilet lift chain is too long it can get in the way of your flapper closing. Adjust the lift chain by shortening it so that there is only a little bit of chain when the flapper is closed. The lift chain should be pulling straight up when the flush handle is pressed.
Or if your flapper is very old, the flapper may be worn out and may not be sealing properly. This can happen when debris gets in between the flapper and the flush valve for the water to go through.
Without the flapper forming a tight seal water, the water supply will be minimal. That’s because the water will leak through to the toilet bowl and your tank will not fill up. This will lead to a weak flushing toilet or no flush all.
Inspect the overflow tube
The overflow tube can crack and it will continuously send the flow of water into the toilet bowl. This can be a cause of water constantly running and your tank not filling up.
If this happens you will need to replace the overflow tube. It’s a very straightforward repair as long as you buy the right tube size.
Inspect the float
Make sure that the float is coming all the way up to the top. These can have a float ball attached to the float arm, or a float cup on the fill valve.
Gently grab the toilet fill valve and slide the float cup up to see if that is the issue. If water starts to rise and push the float back to its normal resting position you may have fixed it right then and there. Give the toilet handle another flush to see if this corrects the issue. The fill valve float should come up to the top.
If you have a float ball, it’s likely you have an older toilet and things could be breaking down. Check the float arm and float ball to make sure they are set to the proper level. These arms can be bent and cause the float ball to sit too long causing your tank not to fill up.
If the float valve is set too low or is stuck the tank isn’t filling to its proper level and it will need to be adjusted.
The water level needs to be about half an inch below the overflow tube, you will want it to reach that level to ensure a strong flushing toilet. Filling the tank shouldn’t take any more than 10 to 15 seconds to fill depending on the water pressure you have in the house.
Related: Toilet Keeps Running ? Here’s how to fix it!
Check the trip assembly
The trip assembly is the part that comes from the toilet handle into the tank. If the lever gets bent or worn out it could be causing issues with other parts of the tank and should be replaced.
Next inspect the fill valve
Look at the fill valve to see if water is coming through it. If there is no water coming into the tank you will need to inspect the fill valve for a blockage. Your fill valve may have debris build up and simply cleaning it off can do the trick.
If neither of these are the issue it could be that there is debris in the line coming to the toilet or in the fill valve.
Step 3: Turn off the water supply
Before you go any further you should turn off the water supply of the toilet. This will be found at the base of the toilet by the floor or going into the wall. Next you will want to flush the toilet to remove any water from the tank.
Step 4: Flush out the fill vale to remove any debris
If water is slowly coming into the tank or not coming in at all it’s likely that the fill valve is broken or clogged.
Check first to see if it is clogged and remove any debris from inside the valve by doing the following:
1. Remove the cap of the fill valve.
To do this grab the shaft of the valve with one hand while you turn the cap of the valve with the other counter clockwise. This will remove the cap and the lever from the rest of the valve.
2. Inspect the seal
Inspect the seal inside the cap to make sure that it is clean of debris and not worn out.
3. Cover valve with an upside down cup
Next get a plastic cup upside down overtop of the shaft of the valve
4. Turn water on to flush it out
With the cup upside down and ready to catch any water, turn the water back on and allow the water to run for 30 seconds so that any debris can be pushed out. Once the water is flowing again fully turn the water off.
If there was no water or very little water coming through the top of the fill valve, move on to the next step, as your pipe coming into the toilet may be clogged.
5. Replace fill valve cap
Once that is done put the cap back on by giving it a turn clockwise.
6. Turn water back on
Turn the water back on and see if the tank fills back up. If it is filling up again you have fixed the problem.
Step 5: Unclog the main line into the tank.
If removing the debris from the fill valve didn’t work, or if there was minimal water pressure coming up through it it’s likely that the main line into the tank is clogged. Here is what you need to do to unclog the line coming into your toilet.
- Make sure the water is still off.
- Pace a large bowl underneath the shut-off valve to catch the water.
- Use a wrench to loosen the lock nut from the main line to the shut-off valve.
- Inspect the line to see if there are any blockages. Use a pipe cleaner or this device to try and remove any buildup that’s happened in the pipe.
- Reattach the pipe to the shut off valve and snuggle with wrench.
- Turn the tank back on and make sure the reattached hose is not leaking or dripping water.
- See if water is coming into the tank at a good water pressure.
- Flush the toilet again and see if the water pressure has increased and water is filling the tank.
If this didn’t fix the issue it’s likely that there is a problem with your fill valve and needs to be replaced.
Related: Read this if you have low hot water pressure.
How to Replace a Toilet Fill Valve
If you’ve adjusted the toilet fill valve and nothing seems to be working you may need to replace it. Replacing the fill valve can be done using these simple steps.
- Turn off water to the toilet tank at the main line shut off valve (look underneath the tank on the floor or coming out of the wall for the knob).
- Place a bowl underneath the main line and the tank to catch any water.
- Flush the toilet to remove any water from the tank.
- Disconnect the main water line coming into the toilet from the shut-off valve.
- Remove the lock nut underneath the base of the tank by turning it counterclockwise.
- Detach the line from the cap of the fill valve from the overflow tube.
- Remove the fill valve.
- Drain the remaining water from the tank.
- Clean the area of the hole where the new fill valve will be going to ensure a tight seal.
- Insert the new fill valve into the tank and tighten the nut underneath with your hand at first and then snug with a pair of pliers
- Attach the tube from the fill valve to the overflow tube
- Reattach the water line and snug with pliers or wrench
- Gently turn on the shut off valve to restore water flow.
- Watch the water fill up the tank and inspect for any leaks. If any leaking water snug the parts a little more.
- Adjust the fill valve float to the right water level and flush the toilet.
- Ensure tank is filling up to the water level indicated by the manufacturer.
- Replace the lid of the tank.
- Make sure the toilet bowl is filling up its normal level.
There you go you have replaced the toilet fill valve and your toilet should be filling up again like it is brand new.
Final thoughts on toilet tank not filling with water
Your tank can easily be fixed using the methods above. If you have tried these and nothing seems to work. Or you still can’t get water coming into your tank, it’s possible that there is an issue before the water is reaching the shut off valve to the toilet. If this is the case, you will need to contact a professional plumber to help you with this. Use the link below to find a plumber in your area.